ShellyPlugS mit ESPHome

Schritt für Schritt Anleitung:
Power Plug S von Shelly kann ohne löten direkt über WLAN (OTA) geflasht werden.

Dazu müsst Ihr lediglich die folgenden Schritte durchführen:
Schritt 1: Diesen Link inkl. der IP vom Shelly Plug S im Browser aufrufen
http://Hier_Deine_Ip_Vom_Plug/ota?url=http://dl.dasker.eu/firmware/mg2tasmota-ShellyPlugS.zip
Danach ein wenig Geduld
Schritt 2: Eine ältere Version von Tasmota flashen
http://ota.tasmota.com/tasmota/release-7.2.0/tasmota-minimal.bin
Schritt 3: Nun erzeugt ihr euch eine BIN Datei im ESPHome mit dem Codebeispiel unten
Schritt 4: Über die Oberfläche von Tasmota könnt ihr nun die BIN Datei von ESPHome OTA flashen.
Schritt 5: Im Home Asssitant sollte ein neues Gerät gefunden werden was ihr einbinden könnt.

[asa2 id=“5787″ tpl=“Horizontal_box“/]

Codebeispiel:

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
substitutions:
  devicename: shelly-plug-s-1
  channel_1: Relay


  ssid: SSID
  password: PASSWORT

  # Higher value gives lower watt readout
  current_res: "0.000943"
  # Lower value gives lower voltage readout
  voltage_div: "2066"
  # measure a relatively strong load and enter values measured by the device vs the values your reference measurement provided here
  power_cal_meas: "1710.0"
  power_cal_real: "1685.0"

  max_power: "2500"
  max_temp: "70.0"

esphome:
  name: ${devicename}

esp8266:
  board: esp8285

wifi:
  ssid: ${ssid}
  password: ${password}


  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: ${devicename}
    password: ${password}


captive_portal:

# Enable logging
logger:
  level: DEBUG

# Enable Home Assistant API
api:


ota:


web_server:
  port: 80

time:
  - platform: sntp
    id: my_time

binary_sensor:
  - platform: gpio
    pin:
      number: GPIO13
      inverted: True
    name: "${devicename}_button"
    on_press:
      - switch.toggle: relay

status_led:
  pin:
    number: GPIO02
    inverted: True

output:
  - platform: gpio
    pin: GPIO00
    inverted: true
    id: led

switch:
  - platform: gpio
    pin: GPIO15
    id: relay
    name: "${channel_1}"
    on_turn_on:
      - output.turn_on: led
    on_turn_off:
      - output.turn_off: led

sensor:
  - platform: wifi_signal
    name: "${devicename} WiFi Signal"
    update_interval: 300s

  # NTC Temperature
  - platform: ntc
    sensor: temp_resistance_reading
    name: ${devicename} temperature
    unit_of_measurement: "°C"
    accuracy_decimals: 1
    icon: "mdi:thermometer"
    calibration:
      b_constant: 3350
      reference_resistance: 10kOhm
      reference_temperature: 298.15K
    on_value_range:
      - above: ${max_temp}
        then:
          - switch.turn_off: relay
          - homeassistant.service:
              service: persistent_notification.create
              data:
                title: Message from ${devicename}
              data_template:
                message: Switch turned off because temperature exceeded ${max_temp}°C
  - platform: resistance
    id: temp_resistance_reading
    sensor: temp_analog_reading
    configuration: DOWNSTREAM
    resistor: 32kOhm
  - platform: adc
    id: temp_analog_reading
    pin: A0

  - platform: hlw8012
    model: BL0937
    sel_pin:
      number: GPIO12
      inverted: true
    cf_pin: GPIO05
    cf1_pin: GPIO14
    current_resistor: ${current_res}
    voltage_divider: ${voltage_div}
    current:
      name: "${channel_1} current"
      unit_of_measurement: "A"
      accuracy_decimals: 3
      icon: mdi:flash-outline
    voltage:
      name: "${channel_1} voltage"
      unit_of_measurement: "V"
      icon: mdi:flash-outline
    power:
      name: "${channel_1} power"
      id: power
      unit_of_measurement: "W"
      filters:
        - calibrate_linear:
          - 0.0 -> 0.0
          - ${power_cal_meas} -> ${power_cal_real}
      icon: mdi:flash-outline
      on_value_range:
        - above: ${max_power}
          then:
            - switch.turn_off: relay
            - homeassistant.service:
                service: persistent_notification.create
                data:
                  title: Message from ${devicename}
                data_template:
                  message: Switch turned off because power exceeded ${max_power}W
    update_interval: 10s

  - platform: total_daily_energy
    name: "${channel_1} daily energy"
    power_id: power
    filters:
      # Multiplication factor from W to kW is 0.001
      - multiply: 0.001
    unit_of_measurement: kWh

📦 Das könnte dir gefallen

Codebeispiel:

Passende sensor-Produkte

Artikel teilen